武漢格萊莫檢測設備有限公司
電話:13545068882;027-86619889
傳真:027-86619889
網址:www.glmgs.com www.gelaimo.com
http://www.glmgs.com/prodxx.asp?id=216
一、用途及適用範圍
SYD-0703型液壓式車轍試樣成型機是根據中華人民共和國行業標準JTJ052《公路工程瀝青及瀝青混合料試驗規程》中的T0703《瀝青混合料試件制作方法(輪碾法)》規定的要求設計制造的,主要用於車轍試驗時對瀝青混合料試驗做碾壓成型,也適用於瀝青混合料其它物理、力學性能試驗的碾輪法試樣制作。
本儀器集機械、電氣、液壓為一體,和同類產品相比,具有體積小、自動化程度高、功能強、操作方便等特點,是瀝青混合料碾壓成型的理想儀器。
二、主要技術指標和參數
1、試模規格: 300mm×300mm×(30㎜∼100mm);
2、試模車行程: 300mm;
3、試模車運動速度: 6次往返/分鐘;
4、試模高度變化值: 30㎜∼100mm;
5、碾輪壓力: 0kN∼20kN內,可任意調整;
6、碾輪規格: 半徑為500mm,寬度為300mm;
7、碾輪預熱: 20℃∼200℃,可任意設定(通常設定為100℃);
8、碾壓輪線壓力: 300N/cm;
(碾壓輪寬為30cm,故正壓力應為9kN );
9、整機外型尺寸: 1750㎜×1216㎜×640mm;
10、整機重量: 500kg。
11、工作電源: AC380V±10%,50Hz;
12、整機功耗: 3000W。
一、用途及適用範圍
One, use and scope
SYD-0703型液壓式車轍試樣成型機是根據中華人民共和國行業標準JTJ052《公路工程瀝青及瀝青混合料試驗規程》中的T0703《瀝青混合料試件制作方法(輪碾法)》規定的要求設計制造的,主要用於車轍試驗時對瀝青混合料試驗做碾壓成型,也適用於瀝青混合料其它物理、力學性能試驗的碾輪法試樣制作。
SYD-0703 type hydraulic rutting test specimen forming machine is based on the standard of people's Republic of China JTJ052 " highway engineering asphalt and asphalt mixture test code " T0703 " in asphalt mixture specimen preparation method ( grinding method " ) in accordance with the requirements of design and manufacture, mainly used in the rutting test of asphalt mixture test compaction of asphalt mixture, also applies to other physical, mechanical properties test method of making sample grinding wheel.
本儀器集機械、電氣、液壓為一體,和同類產品相比,具有體積小、自動化程度高、功能強、操作方便等特點,是瀝青混合料碾壓成型的理想儀器。
The instrument integrates mechanical, electrical, hydraulic integration, and compared to similar products, has the advantages of small volume, high degree of automation, strong function, convenient operation, is the ideal Asphalt Mixture Compaction apparatus.
二、主要技術指標和參數
In two, the main technical indexes and parameters
1、試模規格: 300mm×300mm×(30㎜∼100mm);
1, test specifications: 300mm ×300mm ×( 30 mm to 100mm);
2、試模車行程: 300mm;
2, try to die car journey: 300mm;
3、試模車運動速度: 6次往返/分鐘;
3, test mode vehicle speed: 6 round / min;
4、試模高度變化值: 30㎜∼100mm;
4, try to die height change value: 30 mm to 100mm;
5、碾輪壓力: 0kN∼20kN內,可任意調整;
5, roller pressure: 0kN ~ 20kN, can be arbitrarily adjusted;
6、碾輪規格: 半徑為500mm,寬度為300mm;
6, grinding wheel specifications: radius is 500mm, width of 300mm;
7、碾輪預熱: 20℃∼200℃,可任意設定(通常設定為100℃);
7, roller preheating: 20℃ ~ 200 ℃, can be arbitrarily set ( usually set at 100 degrees C);
8、碾壓輪線壓力: 300N/cm;
In 8, the rolling wheel line pressure: 300N/cm;
(碾壓輪寬為30cm,故正壓力應為9kN );
( the rolling wheel width of 30cm, the pressure shall be 9kN );
9、整機外型尺寸: 1750㎜×1216㎜×640mm;
9, overall size: 1750 mm x 1216 mm× 640mm;
10、整機重量: 500kg。
In 10, the whole machine weight: 500kg.
11、工作電源: AC380V±10%,50Hz;
In 11, a working power supply: AC380V ± 10%, 50Hz;
12、整機功耗: 3000W。
12, overall power consumption: 3000W.