本特利3500/20模塊
本特利3500/20模塊
產品詳情資料：
本特利3500/42監測器為4通道監測器，可接收來自電渦流式位移傳感器和速度、加速度傳感器( Proximitor and Seismic Transducers)的信號輸入，並根據此輸入去驅動報警。3500/42經過3500框架組態軟件編程可完成如下測量功能：徑向振動、軸向位置、偏心、差脹、加速度、速度。該模塊可接收多種傳感器的輸入，
其中包括以下本特利的傳感器：
bently3500/42監測器的主要功能為：
1)連續地對當前機械的振動與組態的報警設置點進行比較，以驅動報警對機械進行保護，
2)對運行人員和維修人員提供基本的機械振動信息。報警設置點是通過3500框架組態軟件來組態的。
對每個有效的比例值可進行報警設置點的組態，而對於危險設置點只能對所有有效比例值的兩個進行組態。當從制造廠發出時，3500／42未被組態。需要時，3500／42可安裝在3500框架中並組態完成所要求的監測功能。這可使你貯存一單個的監測器用作多種不同應用的條件。
可用數據渦流式位移傳感器／速度、加速度傳感器監測器根據所組態的通道類型返回特定的比例值。該監測器還同時返回監測器和通道的狀態值，這點對各類通道是相同的。
狀態值以下為位移／速度、加速度監測器所產生的狀態。
監測器狀態0K
它指示監測器是否運行正常。在如下的任何一個情況下將返回一個非OK狀態：
a) 模塊中的硬件故障。
b) 結點電壓故障。
c) 傳感器故障。
d) 組態故障。
e) 插槽ID故障。
f) 鍵相器故障(如果鍵相位信號組態給每一對通道)。
g) 通道非OK。
產品英文詳情資料：
The Bentley 3500/42 monitor is a 4-channel monitor that can receive signal inputs from eddy current displacement sensors, velocity and acceleration sensors, and drive alarms based on this input. 3500/42 can complete the following measurement functions through programming with the 3500 rack configuration software: radial vibration, axial position, eccentricity, differential expansion, acceleration, and speed. This module can receive inputs from various sensors,
This includes the following Bentley sensors:
The main functions of the bently3500/42 monitor are:
1) Continuously compare the vibration of the current machinery with the alarm set points configured to drive alarms to protect the machinery,
2) Provide basic mechanical vibration information to operators and maintenance personnel. The alarm setpoints are configured through the 3500 rack configuration software.
Alarm setpoints can be configured for each valid proportional value, while for danger setpoints, only two of all valid proportional values can be configured. When sent from the manufacturing plant, 3500/42 was not configured. When needed, 3500/42 can be installed in the 3500 rack and configured to complete the required monitoring functions. This allows you to store a single monitor for various application conditions.
The eddy current displacement sensor/velocity/acceleration sensor monitor can return specific proportional values based on the configured channel type. The monitor also returns the status values of both the monitor and the channel, which is the same for all types of channels.
Below the state values are the states generated by displacement/velocity and acceleration monitors.
Monitor status 0K
It indicates whether the monitor is functioning properly. A non OK status will be returned in any of the following situations:
a) Hardware failure in the module.
b) Node voltage fault.
c) Sensor failure.
d) Configuration failure.
e) Slot ID fault.
f) Keyphasor failure (if the keyphasor signal is configured for each pair of channels).
g) The channel is not OK.
免責聲明：
AMIKON我們銷售新產品和停產產品，獨立渠道購買此類特色產品。阿米控不是本網站特色產品的授權分銷商、經銷商或代表。本網站上使用的所有產品名稱/產品圖片、商標、品牌和徽標均為其各自所有者的財產。帶有這些名稱,圖片、商標、品牌和徽標的產品描述、描寫或銷售僅用於識別目的，並不表示與任何權利持有人有任何關聯或授權。
| BENTLY NEVADA | 3500/42M 140734-02 | EMERSON | KJ4001X1-HC1 12P0831X072 |
| BENTLY NEVADA | 3500/42M 140734-02 | EMERSON | KJ4001X1-JA1 12P1832X022 |
| BENTLY NEVADA | 3500/42M 176449-02 | EMERSON | KJ4001X1-NA1 12P3373X012 |
| BENTLY NEVADA | 3500/42M 176449-02 | EMERSON | KJ4001X1-NA1 12P3373X022 |
| BENTLY NEVADA | 3500/42M 176449-02 | EMERSON | KJ4001X1-NB1 12P3368X012 |
| FOXBORO | FBM3A/33A P0500RU | SIEMENS | 6ES7431-7KF00-6AA0 |
| FOXBORO | FBM4/39/44 P0500RY | SIEMENS | 6ES7431-7KF10-0AB0 |
| FOXBORO | FBMSSW | SIEMENS | 6ES7954-8LC02-0AA0 |
| FOXBORO | FBMSVH | SIEMENS | 6EW1810-3AA |
| FOXBORO | FCM100ET P0926GS | SIEMENS | 6EW1860-3AA |
| GE | IC697BEM733 | VIBRO METER | VM600 CMC16 200-530-100-014 |
| GE | IC697BEM733 | VIBRO METER | VM600 CPU M 200-595-041-113 |
豫公安備 41010502000017號