BENTLY NEVADA 128229-01 振動模擬量模塊
BENTLY NEVADA 128229-01 振動模擬量模塊
產品詳情資料：
3500/45?監測器的主要功能是：????
1)??通過將所監測參數與設定的報警點進行連續比較並驅動報警，以提供機械保護功能??
2)??為運行人員和維護人員提供基本的機器信息。???
根據組態，每一通道可將輸入信號處理為稱作“比例值”的多種參數。每一個有效比例值可組態為報警設置點，而任意兩個有效比例值可組態為危險設置點。?
前面板LED（發光二極管）：?OK?LED??指示3500/45?運行正常??
TX/RX?LED：指示3500/45?正在與3500框架內其它模塊通訊旁路
LED：指示3500/45?正處於旁路關態??
通過LED進行故障診斷時，3500/45與前面提到的3500/40M相似。?傳感器緩衝輸出：在監測器前面板上每個通道對應有一個同軸接頭。各同軸接頭帶有短路保護。當使用DC?LVDT?時，通道3?和通道4?是-10Vdc?的電平轉換。當使用ACLVDT?時，所有通道均為由LVDT?返回的交流信號的直流顯示。
BENTLY NEVADA 128229-01 振動模擬量模塊
AGND/GUARD模擬接地/防護裝置–當跳線W12位於位置AC時，連接至模塊模擬接地，或當跳線位於位置A-B時，連接到SCXIbus模擬總線防護裝置。否則保持未連接。這些引腳連接到MIO數據採集板的模擬接地。3輸出輸出–主模塊模擬輸出。在掃描模式下，所有八個通道的輸出按順序顯示在此處。
產品英文詳情資料：
The main functions of the 3500/45 monitor are:
1) By continuously comparing the monitored parameters with the set alarm points and driving alarms, mechanical protection functions are provided
2) Provide basic machine information for operators and maintenance personnel. ???
According to the configuration, each channel can process input signals into various parameters called "proportional values". Each valid proportional value can be configured as an alarm set point, while any two valid proportional values can be configured as danger set points. ?
Front panel LED (light emitting diode): OK LED indicates that 3500/45 is operating normally
TX/RX LED: Indicates that the 3500/45 is bypassing communication with other modules in the 3500 rack
LED: Indicates that 3500/45 is in the bypass off state
When using LED for fault diagnosis, the 3500/45 is similar to the previously mentioned 3500/40M. Sensor buffered output: There is a coaxial connector corresponding to each channel on the front panel of the monitor. Each coaxial connector is equipped with short-circuit protection. When using DC LVDT, channels 3 and 4 have a level conversion of -10Vdc. When using ACLVDT, all channels are displayed as DC of the AC signal returned by LVDT.
BENTLY NEVADA 128229-01 振動模擬量模塊AGND/GUARD Analog Ground/Guard – Connected to the module analog ground when jumper W12 is in position AC, or to the SCXIbus analog bus guard when the jumper is in position A-B. Otherwise leave unconnected. These pins connect to the analog ground of the MIO data acquisition boards. 3 OUTPUT Output – Main module analog output. In Scan mode, the outputs of all eight channels appear here in sequence.
免責聲明：
AMIKON我們銷售新產品和停產產品，獨立渠道購買此類特色產品。阿米控不是本網站特色產品的授權分銷商、經銷商或代表。本網站上使用的所有產品名稱/產品圖片、商標、品牌和徽標均為其各自所有者的財產。帶有這些名稱,圖片、商標、品牌和徽標的產品描述、描寫或銷售僅用於識別目的，並不表示與任何權利持有人有任何關聯或授權。
| 本特利 | TK-3E 177313-02-02 | ICS TRIPLEX | T9852 |
| 本特利 | TK-3E | ICS TRIPLEX | T9832 |
| 本特利 | 990-04-70-02-00 | ICS TRIPLEX | T9802 |
| 本特利 | 990-04-70-01-00 | ICS TRIPLEX | T9451 |
| 本特利 | 990-04-50-02-00 | ICS TRIPLEX | T9451 |
| 本特利 | 3500/93 135799-01 | ICS TRIPLEX | T9432 |
| 本特利 | 3500/93 135785-01 | ICS TRIPLEX | T9432 |
| 本特利 | 3500/93 | ICS TRIPLEX | T9402 |
| AB | 3500/93 | ICS TRIPLEX | T9110 |
| 本特利 | 3500/92 | ICS TRIPLEX | T8480C |
| 本特利 | 3500/92 136180-01 | ICS TRIPLEX | T8480C |
豫公網安備41010502000017號 
