你好,歡迎來到世鋁網 [請登錄] [免費注冊]
世鋁網 鋁業產品
您當前的位置: 世鋁網 鋁業產品 鋁型材 CC-PDIL01 51308388-175計數板 3

CC-PDIL01 51308388-175計數板

加入收藏 舉報
詳細信息

產品標題: CC-PDIL01 51308388-175計數板

型號: CC-PDIL01 51308388-175

品牌: 霍尼韋爾


                                                           

                                                                                 產品詳情資料

——DCS正確停電——


第一步:進行斷電前的各項檢查 
1、打開控制站櫃門,觀察卡件是否工作正常,有無故障顯示; 
2
、從每個操作站實時監控的故障診斷中觀察是否存在故障,並進行記錄; 
3
、檢查電源箱是否工作正常,電源風扇是否工作,5V24V指示燈是否正常,測量記錄各電壓值; 
4
、備份組態、PID參數、驅動以及其他需要的重要數據; 
5
、檢查供電冗餘,供電冗餘包括交流供電冗餘和直流供電冗餘。交流供電冗餘:通過分別斷開冗餘交流~220VAC進線的一路,係統有一半的交流供電回路失電,但係統應仍然可以正常工作。直流供電冗餘測試方法如下: 
1)先斷一路電源箱電源,測量每一機籠機籠母板電源端子上5V24V的電壓; 
2)先通上一路電源箱電源,再斷另外一路電源箱電源,再測量每一機籠母板電源端子上5V24V的電壓。電源箱5V輸出電壓應在5.10V5.25V之間,電源箱24V輸出電壓應在23.00V25.00V之間。如果電壓偏差較大需要及時檢查處理,否則會影響卡件的正常工作。 
6
、網線及布置檢查,檢查網絡線纜通斷情況,確認連接處是否接觸良好,並及時更換故障線纜; 
7
UPS測試:通過斷開UPS交流進線,測試UPS電池供電能力。UPS電池應定期放電,一般建議每月一次,放電方法:斷開UPS交流供電採用電池供電,至電池即將釋放完為止。 
 以上檢查主要事先了解係統的運行狀態,如有不正常的現象可以在停車時及時解決。 



第二步:按順序切斷電源 
1、每個操作站依次退出實時監控及操作係統後,關操作站工控機及顯示器電源; 
2
、逐個關控制站電源箱電源; 
3
、關閉各個支路電源開關; 
4
、關閉不間斷電源(UPS)電源開關; 
5
、關閉總電源開關。 


                          產品英文詳情資料:

——DCS correct power outage——


Step 1: Conduct various inspections before power outage


1. Open the control station cabinet door and observe if the card is working properly and if there are any fault displays;


2. Observe and record the existence of faults from the real-time monitoring fault diagnosis of each operating station;


3. Check whether the power box works normally, whether the power fan works, whether the 5V and 24V indicators are normal, measure and record the voltage values;


4. Backup configuration, PID parameters, drivers, and other necessary important data;


5. Check the power supply redundancy, which includes AC power supply redundancy and DC power supply redundancy. AC power supply redundancy: By disconnecting one of the redundant AC~220VAC incoming lines, half of the AC power supply circuit of the system loses power, but the system should still be able to operate normally. The redundancy testing method for DC power supply is as follows:


(1) Firstly, disconnect one power supply box and measure the voltage of 5V and 24V on the power terminals of each cage and cage motherboard;


(2) First connect one power supply box, then disconnect the other power supply box, and then measure the voltage of 5V and 24V on the power terminals of each cage motherboard. The 5V output voltage of the power box should be between 5.10V and 5.25V, and the 24V output voltage of the power box should be between 23.00V and 25.00V. If the voltage deviation is large, it needs to be checked and handled in a timely manner, otherwise it will affect the normal operation of the card.


6. Check the network cable and layout, check the connection and disconnection of the network cable, confirm whether the connection is in good contact, and replace the faulty cable in a timely manner;


7. UPS test: Test the power supply capacity of the UPS battery by disconnecting the UPS AC incoming line. UPS batteries should be discharged regularly, generally recommended once a month. Discharge method: Disconnect UPS AC power supply and use battery power until the battery is about to be discharged.


The above checks mainly focus on understanding the operating status of the system in advance. If there are any abnormal phenomena, they can be promptly resolved during parking.


Step 2: Cut off the power supply in sequence


1. After each operation station exits the real-time monitoring and operating system in sequence, turn off the power supply of the industrial control computer and display of the operation station;


2. Turn off the power supply of the control station power box one by one;


3. Turn off the power switches of each branch;


4. Turn off the uninterruptible power supply (UPS) power switch;


5. Turn off the main power switch.

免責聲明:

AMIKON我們銷售新產品和停產產品,獨立渠道購買此類特色產品。阿米控不是本網站特色產品的授權分銷商、經銷商或代表。本網站上使用的所有產品名稱/產品圖片、商標、品牌和徽標均為其各自所有者的財產。帶有這些名稱,圖片、商標、品牌和徽標的產品描述、描寫或銷售僅用於識別目的,並不表示與任何權利持有人有任何關聯或授權。


DSPC1558C-TAIX61 51306977-175TSXAEM1613 TSX-AEM1613
DSPC172H8C-TAIX51 51306979-175TSXETZ410
DSQC1048C-TAIMA1 51307171-175TSXLES65
DSQC2018C-TAIM01 51306999-175TSXP4720
DSQC2058C-TAIDB1 51307133-175TSXP57153M
DSQC2238C-TAIDA1 51307131-175TSXP67455 TSX6740
DSQC2278C-TAID61 51307069-175XBTF034510
DSQC236G8C-PDODA1 51454472-175XBTGT2220
DSQC236T8C-PDOD51 51454361-175140ARI03010
DSQC2398C-PDILA1 51454471-175 140DDO35300






聯係方式
  • 聯係人: 吳工 女士
  • 電話: 0592-5085207
  • 手機: 18030175270
  • 地址: 福建省 廈門市 思明區湖濱南路388號國貿大廈32D單元
還沒找到合適的產品?