IS215VCMIH1B VME通信接口卡_廈門阿米控技術有限公司

產品標題: FanucIS215VCMIH1B VME通信接口卡

型號： IS215VCMIH1B

品牌： GE

產品詳情資料：

IC698CPE010是GE Fanuc RX7i係列的一款中央處理器。該設備能夠實時控制工業機械和材料過程。它通過安裝在機架上的VME64連接背板與其他設備和模塊進行通信。

IC698CPE010具有300MHz賽揚微處理器，能夠執行浮點計算。每個布爾函數的標準速度為每個線圈0.33ms。該設備的其他功能包括但不限於以下內容：三個嵌入式串行端口和兩個以太網端口、位字參考支持、符號變量支持、測試編輯模式以及網絡數據監控。

該設備具有10兆字節的RAM存儲器，用於存儲數據和編程信息。該存儲器由CMOS電池維持。還提供了額外的10兆字節的非易失性閃存（NVRAM）。操作係統固件數據存儲在閃存中。固件可以在不拆開設備或更換EPROM的情況下進行更新。

操作IC698CPE010有兩種方式：三位運行/停止開關，將設備連接到計算機並運行適當的軟件。可以通過串行或以太網端口將此設備連接到計算機。注意：使用以太網端口需要IP尋址和Cat5電纜。對於串行連接，使用SNP協議。對於該設備的配置和編程，所附計算機上使用Proficy Machine Edition PLC Logic Developer軟件。配置數據由密碼保護。

安裝IC698CPE010時，請按照產品手冊中的說明進行操作。禁用機架電源。記錄設備的媒體訪問控制（MAC）地址。將設備牢固地安裝並接地到機架的一個插槽，即指定的CPU插槽中。連接以太網和串行端口。重新啟用機架電源。將CMOS電池連接到其中一個連接器。開始對設備進行編程。

IC698CPE010 CPU是通用電氣發那科中央處理器。它是RX7i PACSystems係列的工業中央處理器單元。它有助於控制不同的工業應用。CPU配有300 MHz賽揚處理器，支持高達100 Mbps的以太網速度。CPU具有可在額定功率下保持40天內存的功能。CPU具有10 MB的非易失性閃存用戶存儲器。它由5伏總線電壓供電，額定電流為3.2安培。它可以以每1000個布爾觸點/線圈0.195毫秒的速度執行布爾表達式。它的度為每天9秒。CPU多可監控16個web服務器和FTP連接。它的設計非常緊湊，重量只有6.3公斤。它可以很容易地安裝在帶有背板的機架上。工作溫度應設置在0到60攝氏度之間。

GE Fanuc IC698CPE010 CPU通過使用模塊正面VME 64標準格式的以太網端口與編程器和HMI設備進行通信。CPU通過使用引用表來提供對大容量存儲器的訪問。它可以使用不同的編程語言進行編程，包括梯形圖、結構化文本和功能框圖語言。IC698CPE010 CPU配備了支持Modbus RTU從站、SNP和串行I/O協議的串行端口。CPU支持多達512個程序塊。它還允許“測試編輯”模式，可以對正在運行的程序進行修改。IC698CPE010 CPU還支持遠程工作站管理器。

產品英文詳情料:

The IC698CPE010 is a Central Processing Unit from the GE Fanuc RX7i series. This device is capable of controlling industrial machinery and material processes in real-time. It communicates with other devices and modules through a VME64 connection backplane mounted to the rack.

The IC698CPE010 has a 300MHz Celeron microprocessor capable of performing floating point calculations. The standard speed of each Boolean function is 0.33ms per coil. Other features of this device include but are not limited to the following: three embedded serial ports and two Ethernet ports, bit-in-word reference support, symbolic variable support, a Test Edit mode, and data monitoring over the web.

This device has 10 megabytes of RAM memory for data and programming information. This memory is sustained by a CMOS battery. An additional 10 megabytes of non-volatile flash memory (NVRAM) is also provided. The operating system firmware data is stored in flash memory. Firmware can be updated without taking apart the device or replacing the EPROMs.

There are two means to operate the IC698CPE010: the three-position run/stop switch and connecting the device to a computer and running the appropriate software. Connecting this device to a computer is possible via the serial or Ethernet ports. Note: Using the Ethernet port will require IP addressing and a Cat5 cable. For serial connections, the SNP protocol is used. For configuration and programming of this device, Proficy Machine Edition PLC-Logic Developer software is used on the attached computer. Configuration data is secured with a password.

Follow the instructions in the product manual while installing the IC698CPE010. Disable rack power. Document the Media Access Control (MAC) address of the device. Securely mount and ground the device into slot one of the rack, the designated CPU slot. Connect the Ethernet and serial ports. Re-enable power to the rack. Connect the CMOS battery to one of the connectors. Begin programming the device.

The IC698CPE010 CPU is a GE Fanuc Central Processing Unit. It is an industrial central processor unit from the RX7i PACSystems series. It helps to control different industrial applications. The CPU comes with a 300 MHz Celeron processor and it supports Ethernet speeds of up to 100 Mbps. The CPU features memory retention for 40 days of nominal power. The CPU has 10 MB of non-volatile flash user memory. It is powered with 5 Volts bus voltage and it has a current rating of 3.2 Amps. It can execute boolean expressions with a speed of 0.195 milliseconds per 1000 Boolean contacts/coils. It has an accuracy of 9 seconds per day. The CPU can monitor up to 16 web server and FTP connections. It is designed to be compact and it weighs only 6.3 kilograms. It can be easily mounted on a rack with the backplane. The operating temperature should be set between 0 and 60 degrees Celsius.

The GE Fanuc IC698CPE010 CPU communicates with the programmer and HMI devices by using Ethernet ports with the VME 64 standard format on the front side of the module. The CPU provides access to bulk memory by using a reference table. It can be programmed by using different programming languages including the ladder diagram, structured text, and functional block diagram languages. The IC698CPE010 CPU is equipped with serial ports that support the Modbus RTU slave, SNP, and Serial I/O protocols. The CPU features support for up to 512 program blocks. It also allows the “test edit” mode that can make modifications for a running program. The IC698CPE010 CPU also supports remote station managers.

免責聲明：

AMIKON我們銷售新產品和停產產品，獨立渠道購買此類特色產品。阿米控不是本網站特色產品的授權分銷商、經銷商或代表。本網站上使用的所有產品名稱/產品圖片、商標、品牌和徽標均為其各自所有者的財產。帶有這些名稱,圖片、商標、品牌和徽標的產品描述、描寫或銷售僅用於識別目的，並不表示與任何權利持有人有任何關聯或授權。

GE IC693CPU372	Woodward 5417-028	Honeywell 8C-TDIL01 51306856-175
GE IC693DSM302	Woodward 5417-040	Honeywell 8C-PAIN01 51454356-175
GE IC693MDL330	Woodward 5417-175	Honeywell 8C-PAINA1 51454470-175
GE IC693MDL646	Woodward 5437-672	Honeywell 8C-PAON01 51454357-175
GE IC693MDL740	Woodward 5461-644	Honeywell 8C-PAIN01 51454356-175
GE IC693MDL753	Woodward 5461-655	Honeywell 8C-TDIL11 51306858-175
GE IC693PBS105	Woodward 5462-916	Honeywell 8C-TAIX51 51306979-175
GE IC693BEM321	Woodward 5464-211	Honeywell 8C-TAIDB1 51307133-175
GE IC693MDL231	Woodward 5464-643	Honeywell 8CTPOX01 51307022-175